Citron
All posts
·4 min

Dymax and the Problem of Glue You Can't See

Dymax's medical adhesive data sheets lead with cure speed, and the numbers are striking. Its 1193-M-SV05 needle-bonding adhesive reaches fixture in 0.2 seconds under one of Dymax's own BlueWave® LED lamps at 10 W/cm², with full cure typically taking three to five times longer.

What caught our eye is how much of the catalog is about a quieter problem: knowing whether a glue joint is actually there.

Disposable devices are chock-full of small bonds. A needle has to stay put in its hub, a catheter shaft on its manifold, a balloon on its lumen, and every one of those joints is a station on an assembly line. Dymax, which makes light-curable adhesives along with the lamps, conveyors and dispensers that apply and cure them, has built a good deal of chemistry around inspecting those joints and reaching the ones light can't.

Start with clear-on-clear. A transparent adhesive on a transparent plastic is close to invisible, which makes it hard to verify on every part. Dymax's Encompass® technology combines two of its own tricks. See-Cure, which Dymax patented, makes the adhesive dispense blue and turn colorless once it has had enough light, so an operator can check placement and cure at a glance. Ultra-Red® makes the cured adhesive fluoresce bright red under a low-intensity black light. The color works because plastics like PVC and PET naturally glow blue, so a red bond line stands out to a person or a vision system. Dymax adds that Ultra-Red gives off a unique spectral signature manufacturers can use for product authentication.

Then there are shadows. Metal parts, opaque housings and tight overlaps leave pockets a lamp can't reach, a limit every light-curing process has to work around. Dymax's HLC™ (Hybrid Light-Curable) platform combines the anionic chemistry behind instant adhesives with free-radical light curing, so the adhesive starts to cure on contact in dark areas and light speeds it up and strengthens the bond. Light curing also cuts down on blooming, the white residue cyanoacrylates can leave along a bond line. HLC-M-1000, a 3 cP wicking grade, came out in June 2023, and in May Dymax added HLC-M-1004, a 1,300 cP grade aimed at catheters and parts with opaque substrates. Because moisture can set the material off early, Dymax sells dedicated dispensing systems to keep it from curing inside fluid lines.

Catheters get a grade of their own. PEBA and Nylon 12 are common shaft materials and often hard to bond, and Dymax recommends 215-CTH-UR-SC, LED-curable at 385 nm, for balloon/lumen, hub/lumen, marker band and manifold joints. In Dymax's own benchmarking of five tube-to-connector pairings, the low-viscosity version pulled 10% to 30% stronger than a competing adhesive. As with any supplier's benchmark, it's worth confirming on your own parts and materials.

Two limits are worth knowing before you spec any of this. The MD® adhesives are meant for short-term (under 29 days) or single-use disposable devices, and Dymax does not authorize them for long-term implants. And photoinitiator chemistry is changing across the industry: the EU reclassified TPO as toxic for reproduction, Category 1B, from September 1, 2025, and Dymax has been expanding its TPO-free medical range in response.

Dymax has been at this since 1980, when Andy and Clai Bachmann started it in the basement of their home. It's still privately owned and family-run, with more than 550 people at eight locations.

If your line already uses vision inspection, the fluorescing and color-change features are worth evaluating during qualification, before a bond-verification step gets designed around adhesives that can't be seen.

### Sources

Disclaimer: This article is put together on a best-effort basis from publicly available information, including company websites, press releases, and trade publications, as of the date of publication. Specifications, certifications, products, and company details can change, so confirm anything important directly with the supplier. Opinions are the author’s own. Mentions of a company, product, or marketplace are not endorsements or sponsorships, and nothing here is professional, engineering, regulatory, or purchasing advice.

Back to all posts