Zeus makes the liners and heat shrink inside many catheters. But what about the products that are thrown away before the device ships?
Anyone who has built a braided catheter shaft knows the step nobody likes. After reflow, the fusing sleeve that pressed the jacket into the braid has to come off, and for years that meant an operator skiving FEP away with a blade, close enough to the shaft to nick it.
That small, unglamorous problem is a good way into Zeus, the South Carolina polymer company. Zeus has spent decades making the thin parts catheters are built from — PTFE liners with walls down to 0.0004 inch, tubing, heat shrink, and the mandrels everything gets built on. A lot of its recent work goes into the tools and consumables of catheter assembly, the things that never reach the patient.
The sleeve that has to come off
The fusing sleeve does its job in the oven. It shrinks over the jacket, the jacket softens and flows into the braid, and the sleeve is now trapped around a finished shaft. Cutting it off is slow, and a slip of the blade can scrap a part that has already absorbed a good share of its labor cost.
Zeus's answer is FluoroPEELZ™, a peelable heat shrink. It's clear, so an operator can watch the reflow happen, and afterward it tears away along a straight line instead of needing a blade. Zeus recommends recovering it at 420°F (215°C), which is low enough that a PTFE liner underneath won't reflow along with the jacket.
Getting a liner into a hypotube
Laser-cut hypotubes create a different headache. Seating a liner inside one usually means working with very tight clearances and a pressurized system to push the liner out against the wall. In June, Zeus launched XpanCore™ mandrels, made from FEP or PFA, that expand when heated and press the liner outward against the tube instead. The idea is to make the clearance problem a heating step.
Thinner walls, tighter tolerances
The parts that do stay in the device keep getting thinner. Zeus's PTFE Sub-Lite-Wall™ liners come in inside diameters from 0.002 to 0.500 inch, with walls of 0.001 to 0.005 inch, and the family also includes FEP, PFA and PEEK. The StreamLiner™ series goes thinner. It comes as a free-extruded liner, as an over-the-wire version shipped on silver-plated copper or stainless steel wire, and as NG, made by a proprietary film-cast process that Zeus says reduces pinholes.
In August, Zeus added PET Sub-Lite-Wall™ heat shrink, with walls as thin as 0.00025 inch depending on the inside diameter and a wall tolerance down to ±0.0001 inch — roughly one-thirtieth the width of a typical human hair. At that scale, a speck of dust is a defect and a few degrees of drift on the line is scrap.
Every ten-thousandth of an inch saved on a liner or a jacket goes back into the working channel or comes off the outer profile, and that tiny change can determine whether a vessel can be reached at all. Published wall and tolerance figures like these make it easier to compare liners on paper.
The PTFE question
Liners are where the regulatory pressure is building. PTFE has been the default catheter liner for decades, and in January Zeus introduced its PFX™ platform as its next-generation liner platform. The first product, PFX Flex™ Sub-Lite-Wall™, is a non-fluorinated alternative to film-cast PTFE. According to Zeus, its lubricity and flexibility match PTFE's and come from the material itself, without additives or coatings. It bonds covalently to thermoplastics without chemical etching and can be sterilized with gamma and e-beam as well as EtO. Sizes run from 0.013 to 0.387 inch ID, with walls of 0.0015 to 0.003 inch.
In July, Intertek certified PFX Flex liners as PFAS-free, which requires total organic fluorine below 20 ppm and targeted PFAS compounds below 25 ppb. Zeus describes them as the first medical device components to earn that certification. Three more products are on its roadmap: PFX Max, a stronger liner with thinner walls and tighter tolerances; PFX Peelz, a non-fluorinated peelable heat shrink; and PFX Glide, an alternative to polyimide with lubricious additives.
Who builds the rest
Zeus also builds whole catheters now. In June 2021 it bought CathX Medical, a San Jose contract manufacturer, which extrudes Pebax, nylon and polyurethane tubing from 0.010 to 0.300 inch OD at ±0.0005 inch, builds braid- and coil-reinforced shafts from 1.5F to 38F, and makes balloon catheters as small as 0.014 inch. It added a 75,600-square-foot plant in Arden Hills, Minnesota, in September 2023, and in August CathX leased a site in Cartago, Costa Rica, expected to start catheter sub-assembly in Q2 2027 with about 100 new hires.
The plan is to develop and run low volumes in San Jose and Arden Hills, then move programs to Costa Rica on the same quality system and tooling. Matt Bradbury, CathX's vice president of catheter solutions, put the reasoning plainly: "Everyone in this business knows where programs stall, and it's almost never the science, it's the handoff from development into full-scale production."
(For the record: Zeus was founded in 1966, is headquartered in Orangeburg with more than 2,200 employees, and has been owned by the EQT X fund since early 2024. Paddy O'Brien has been CEO since April 2024. The Orangeburg quality system is certified to ISO 13485:2016 by NSF-ISR.)
If you're qualifying a new shaft design, it's worth asking your liner and heat shrink suppliers about the process aids as well as the parts. The sleeve you peel off and the mandrel you pull out can affect your scrap rate as much as anything in the bill of materials.
### Sources
- Zeus: History of Zeus
- EQT: EQT Private Equity to acquire Zeus (Dec 18, 2023)
- Zeus: EQT Private Equity has acquired Zeus
- Irish CCPC merger announcement M/24/001 (Jan 24, 2024)
- PR Newswire: Zeus names new CEO (Mar 14, 2024)
- Zeus: PFX platform launch (Jan 28, 2026)
- Zeus: Intertek PFAS-free certification (Jul 29, 2026)
- Zeus: XpanCore mandrels (Jun 10, 2026)
- Zeus: PET Sub-Lite-Wall heat shrink (Aug 19, 2026)
- Zeus: CathX Medical Costa Rica facility (Aug 13, 2026)
- Zeus: CathX Medical integration (Jun 9, 2021)
- MPO: Zeus acquires CathX Medical
- Zeus: Global expansion program (Jun 20, 2022)
- Zeus: Minnesota expansion key facts (PDF)
- Zeus: Arden Hills grand opening (Sep 14, 2023)
- Zeus/CathX: Catheter manufacturing capabilities
- Zeus: Catheter liners specifications
- Zeus: StreamLiner series
- Zeus: Sub-Lite-Wall tubing
- Zeus: ISO 13485:2016 certificate (NSF-ISR)
- Zeus: FluoroPEELZ peelable heat shrink
- Zeus: PFX Flex Sub-Lite-Wall
- Zeus: Medical brochure (certifications)
- Citron: Zeus supplier directory profile
Disclaimer: This article is put together on a best-effort basis from publicly available information, including company websites, press releases, and trade publications, as of the date of publication. Specifications, certifications, products, and company details can change, so confirm anything important directly with the supplier. Opinions are the author’s own. Mentions of a company, product, or marketplace are not endorsements or sponsorships, and nothing here is professional, engineering, regulatory, or purchasing advice.